3D-Probe

€149.00*

shipping weight 0.3 kg

Available, delivery time 1-3 days (Abroad may vary)

Product number: SW10094

Product information "3D-Probe"

The sensor 3D-Probe is suitable for use as a 3D probe with WinPC-NC or other control software. With the 3D-Probe, non-planar surfaces can be measured automatically and three-dimensional bodies can be scanned precisely. Further applications are the precise determination of the center of a hole or the probing of the zero point or edges of a workpiece.

The probe tip is replaceable and can be reordered individually if required. The probe housing is dust-protected and the probe tip can be mechanically calibrated via three screws.

For more information about the auto-levelling function in WinPC-NC with the 3D-Probe and about the probe itself, please refer to the Documentation tab.

Scope of delivery:

3D-Probe
Holder for 3D-Probe
Spare cover for touch tip made of plastic
Connection cable 2m with magnetic connector
25 pole screw terminal for easy connection to control hardware

Recommended accessories

Surface and length sensor Z-Probe

The Z-Probe surface and length probe can be used both as a flying probe for determining the Z zero point and as a permanently installed probe for determining and correcting tool lengths. For more information on Z zero point determination, the use of a fixed probe with consideration of the workpiece thickness in WinPC-NC, please refer to the Documentation tab.Scope of delivery:Z-ProbeConnection cable 2m with magnetic connector 25 pole screw terminal for easy connection to control hardware

€89.00*

Exchangeable touch tip with M2.5 Thread for 3D-Probe

This set allow you to use touch tips with different lengths on the 3D-Probe sensor.The installation of the exchangeable touch tips is easily possible and does not require any special knowledge.Contents:1x holder for exchangeable touch tips with M2.5 internal thread, height 25mm 1x touch tip with M2.5 external thread, length 16mm, diameter of probe ball 2mm 1x probe tip with M2.5 external thread, length 36mm, diameter of probe ball 2mm 2x silicone dust seal

€59.00*

Tip

Handwheel HR-20

The HR-20 handwheel is equipped with a replaceable 3 m cable and USB plug. With the new, more ergonomic housing, the HR-20 fits even better in the hand and can be perfectly stowed away on the CNC machine with the retaining bracket. The axes are conveniently controlled on the HR-20 via a rotary switch. The handwheel is automatically integrated by Windows and only needs to be activated in the WinPC-NC parameters under Basic Settings-interface. Start today and experience a new dimension of machine operation with WinPC-NC and the HR-20 handwheel. The HR-20 handwheel supports the following functions: Selection of all 4 axesVery precise positioning thanks to high-resolution rotary encoder Step-by-step movement with adjustable width Continuous movement as long as it is turned Special speed mode with variable speed Start/stop of loaded jobs Save and approach zero points Switch spindle and cooling on/off Speed and spindle override during job The HR-20 handwheel information sheet can be downloaded here. The HR-20 handwheel can be used with all WinPC-NC versions from version 2.5 or higher.

€269.00*

Tip

Handwheel HR-10

The handwheel HR-10 is perfect for operating your machine via WinPC-NC. The housing is made of robust plastic and fits very well in the hand. In addition, it has a non-slip rubber cover. The handwheel is controlled via the USB interface on the PC. For this purpose, the handwheel HR-10 has an integrated 3m long USB cable.The handwheel HR-10 supports the following functions:Selection of all 4 axes with displayVery precise positioning by rotary encoder with 100 divisionStep-by-step movement with adjustable distanceContinuous movement as long as rotation is in progressSpecial speed mode with variable speedStart/stop of loaded jobsSave and approach zero pointsSpindle and cooling on/offSpeed and spindle override with potentiometer during jobThe info sheet for the handwheel HR-10 can be downloaded here.The handwheel HR-10 can be used with all WinPC-NC variants from versions 2.5 or higher.

€249.00*

Power supply for ncNET

The ncNET module requires an external supply voltage. This power supply unit is ideal for the ncNET module and is simply connected to the hollow socket of the ncNET module with reverse polarity protection. The cable of the plug-in power supply has a length of 1.5m. Electrical values: Input voltage: 100-240 VAC Output voltage: +12VDC Output current: 1,5A

€6.80*

5-port unmanaged Switch - for ncNET

The ncNET module from WinPC-NC NET can be connected either directly to the control computer or via an existing network hub or switch.If no suitable connection space is available next to the CNC machine, the network can simply be extended plug & play with this unmanaged switch. The switch is specially tested for use with WinPC-NC NET.Details:5x 10/100/1000Mbit/s auto-negotiation RJ45 portsPlug&Play, no configuration necessaryIEEE 802.3x for reliable data flow controlMetal housing for easy installationAuto MDI/MDIX detection, no cross-over cable requiredPacket forwarding rate: 7.4 MBit/sFanlessDimensions 99.8x98x25 mm Scope of delivery:5-port unmanaged network switchOperating instructionsPlug-in power supply unit to supply the network switch3m Ethernet connection cable for the connection from the control computer to the switch

€33.00*

12V Power supply

Some of our components like the Double Axes board or the PWM-5V/10V board need an external supply voltage. For this we offer a 12V power supply with labeled connectors. The cable of the plug-in power supply has a length of 1.5m. Electrical values: Input voltage: 100-240 VAC Output voltage: +12VDC Output current: 1,8A

€8.00*

Spare touch tip 2mm for 3D-Probe

Spare touch tip 2mm for 3D sensor 3D-Probe. The diameter of the touch ball is 2mm.Content: 1 piece

€16.00*

Spare cover for touch tip 3D-Probe

Spare cover for touch tip of our 3D sensor 3D-Probe. Content: 3 pieces

€12.00*